資料下載
羊腫瘤壞死因子α(TNF-α)ELISA Kit中英文雙版說明書
閱讀:425 發布時間:2012-11-19羊腫瘤壞死因子α(TNF-α)試劑盒使用說明書
本試劑盒僅供研究使用。
檢測范圍: 96T
50 ng/L-1300 ng/L
使用目的:
本試劑盒用于測定羊血清、血漿及相關液體樣本中腫瘤壞死因子α(TNF-α)含量。
試劑盒組成
1 | 30倍濃縮洗滌液 | 20ml×1瓶 | 7 | 終止液 | 6ml×1瓶 |
2 | 酶標試劑 | 6ml×1瓶 | 8 | 標準品(2400 ng/L) | 0.5ml×1瓶 |
3 | 酶標包被板 | 12孔×8條 | 9 | 標準品稀釋液 | 1.5ml×1瓶 |
4 | 樣品稀釋液 | 6ml×1瓶 | 10 | 說明書 | 1份 |
5 | 顯色劑A液 | 6ml×1瓶 | 11 | 封板膜 | 2張 |
6 | 顯色劑B液 | 6ml×1/瓶 | 12 | 密封袋 | 1個 |
標本要求
1.標本采集后盡早進行提取,提取按相關文獻進行,提取后應盡快進行實驗。若不能馬上進行試驗,可將標本放于
2.不能檢測含NaN3的樣品,因NaN3抑制辣根過氧化物酶的(HRP)活性。
羊腫瘤壞死因子α試劑盒操作步驟
1. 標準品的稀釋:本試劑盒提供原倍標準品一支,用戶可按照下列圖表在小試管中進行稀釋。
1200 ng/L | 5號標準品 | 150μl的原倍標準品加入150μl標準品稀釋液 |
600 ng/L | 4號標準品 | 150μl的5號標準品加入150μl標準品稀釋液 |
300 ng/L | 3號標準品 | 150μl的4號標準品加入150μl標準品稀釋液 |
150 ng/L | 2號標準品 | 150μl的3號標準品加入150μl標準品稀釋液 |
75 ng/L | 1號標準品 | 150μl的2號標準品加入150μl標準品稀釋液 |
3. 溫育:用封板膜封板后置
4. 配液:將30倍濃縮洗滌液用蒸餾水20倍稀釋后備用
5. 洗滌:小心揭掉封板膜,棄去液體,甩干,每孔加滿洗滌液,靜置30秒后棄去,如此重復5次,拍干。
6. 加酶:每孔加入酶標試劑50μl,空白孔除外。
7. 溫育:操作同3。
8. 洗滌:操作同5。
9. 顯色:每孔先加入顯色劑A50μl,再加入顯色劑B50μl,輕輕震蕩混勻,
10. 終止:每孔加終止液50μl,終止反應(此時藍色立轉黃色)。
11. 測定:以空白空調零,450nm波長依序測量各孔的吸光度(OD值)。 測定應在加終止液后15分鐘以內進行。
羊腫瘤壞死因子α試劑盒注意事項
1.試劑盒從冷藏環境中取出應在室溫平衡15-30分鐘后方可使用,酶標包被板開封后如未用完,板條應裝入密封袋中保存。
2.濃洗滌液可能會有結晶析出,稀釋時可在水浴中加溫助溶,洗滌時不影響結果。
3.各步加樣均應使用加樣器,并經常校對其準確性,以避免試驗誤差。一次加樣時間控制在5分鐘內,如標本數量多,推薦使用排槍加樣。
4. 請每次測定的同時做標準曲線,做復孔。如標本中待測物質含量過高(樣本OD值大于標準品孔*孔的OD值),請先用樣品稀釋液稀釋一定倍數(n倍)后再測定,計算時請zui后乘以總稀釋倍數(×n×5)。
5. 封板膜只限一次性使用,以避免交叉污染。
6.底物請避光保存。
7.嚴格按照說明書的操作進行,試驗結果判定必須以酶標儀讀數為準.
8.所有樣品,洗滌液和各種廢棄物都應按傳染物處理。
9.本試劑不同批號組分不得混用。
10. 如與英文說明書有異,以英文說明書為準。
保存條件及有效期
1.試劑盒保存:;2
2.有效期:6個月
Mouse Tumor necrosis factor α
FOR RESEARCH USE ONLY |
Assay range:25ng/L -800ng/L 96 determinations
Purpose
This kit allows for the determination of TNF-α concentrations in Mouse serum, cell culture supernates and other biological fluids
Principle of the assay
The kit assay Mouse TNF-α level in the sample,use Purified Mouse TNF-α antibody to coat microtiter plate wells, make solid-phase antibody, then add TNF-α to wells, Combined antibody which With HRP labeled goat anti-mouse become antibody - antigen - enzyme-antibody complex, after washing Compley, Add TMB substrate solution,TMB substrate becomes blue color At HRP enzyme-catalyzed, reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm. The concentration of TNF-α in the samples is then determined by comparing the O.D. of the samples to the standard curve.
Materials provided with the kit
1 | wash solution | 20ml×1bottle | 7 | Stopp Solution | 6ml×1 bottle |
2 | HRP-Conjugate reagent | 6ml×1 bottle | 8 | Standard(1600ng/L) | 0.5ml×1 bottle |
3 | Microelisa stripplate | 12well×8strips | 9 | Standard diluent | 1.5ml×1bottle |
4 | Sample diluent | 6ml×1 bottle | 10 | Instruction | 1 |
5 | Chromogen Solution A | 6ml×1 bottle | 11 | Closure plate membrane | 2 |
6 | Chromogen Solution B | 6ml×1 bottle | 12 | Sealed bags | 1 |
1. extract as soon as possible after Specimen collection,and according to the relevant literature, and should be experiment as soon as possible after the extraction. If it can’t, specimen can be kept in
2. Can’t detect the sample which contain NaN3, because NaN3 inhibits HRP active.
Assay procedure
1. Dilute and add sample:Dilute Original density Standard as follow table:
800 ng/L | 5 Standard | 150μl Original density Standard+150μl Standard diluent |
400 ng/L | 4 Standard | 150μl 5 Standard+150μl Standard diluent |
200 ng/L | 3 Standard | 150μl 4 Standard+150μl Standard diluent |
100 ng/L | 2 Standard | 150μl 3 Standard +150μl Standard diluent |
50 ng/L | 1 Standard | 150μl 2 Standard +150μl Standard diluent |
2.add sample:Set blank wells separay (blank comparison wells don’t add sample and HRP-Conjugate reagent, other each step operation is same). testing sample well. add Sample dilution 40μl to testing sample well, then add testing sample 10μl (sample final dilution is 5-fold), add sample to wells , don’t touch the well wall as far as possible, and Gently mix.
3.Incubate: After closing plate with Closure plate membrane ,incubate for 30 min at
4.Configurate liquid: 30-fold wash solution diluted 30-fold (or 20-fold) with distilled water and reserve.
5.washing:Uncover Closure plate membrane, discard Liquid, dry by swing, add washing buffer to every well, still for 30s then drain, repeat 5 times, dry by pat.
6.add enzyme:Add HRP-Conjugate reagent 50μl to each well, except blank well.
7.incubate:Operation with 3.
8.washing:Operation with 5.
9.color:Add Chromogen Solution A 50ul and Chromogen Solution B to each well, evade the light preservation for 15 min at
10.Stop the reaction:Add Stop Solution50μl to each well, Stop the reaction(the blue color change to yellow color).
11.assay:take blank well as zero , Read absorbance at 450nm after Adding Stop Solution and within 15min.
Steps description
Standard, Sample diluent |
Add Standard, Sample diluent, incubate for 30 min at |
Wash 5 time,Add HRP-Conjugate reagent, incubate for 30 min at |
|
Add Stopp Solution |
Read absorbance at 450nm within 15 min |
calculate |
Take the standard density as the horizontal, the OD value for the vertical ,draw the standard curve on graph paper, Find out the corresponding density according to the sample OD value by the Sample curve, multiplied by the dilution multiple, or calculate the straight line regression equation of the standard curve with the standard density and the OD value ,with the sample OD value in the equation, calculate the sample density, multiplied by the dilution factor, the result is the sample actual density.
Important notes
1. The kit takes out from the refrigeration environment should be balanced 15-30 minutes in the room temperature, ELISA plates coated if has not use up after opened, the plate should be stored in Sealed bag.
2. washing buffer will Crystallization separation, it can be heated the water helps dissolve when dilute . Washing does not affect the result.
3. add Sample with sampler Each step, And proofread its accuracy frequently, avoids the experimental error. add sample within 5 min, if the number of sample is much , recommend to use Volley .
4. if the testing material content is excessively higher (The sample OD is bigger than the first standard well ),please dilute Sample (n-fold), Please diluente and multiplied by the dilution factor.(×n×5).
5. Closure plate membrane only limits the disposable use, to avoid cross-contamination.
6. The substrate evade the light preservation.
7. Please according to use instruction strictly, The test result determination must take the microtiter plate reader as a standard.
8. All samples, washing buffer and each kind of reject should according to infective material process.
9. Do not mix reagents with those from other lots.
Storage and validity
1.Storage: 2
2.validity: six months.
羊腫瘤壞死因子α試劑盒應用雙抗體夾心法測定標本中羊腫瘤壞死因子α(TNF-α)水平。用純化的羊腫瘤壞死因子α(TNF-α)抗體包被微孔板,制成固相抗體,往包被單抗的微孔中依次加入腫瘤壞死因子α(TNF-α),再與HRP標記的腫瘤壞死因子α(TNF-α)抗體結合,形成抗體-抗原-酶標抗體復合物,經過*洗滌后加底物TMB顯色。TMB在HRP酶的催化下轉化成藍色,并在酸的作用下轉化成zui終的黃色。顏色的深淺和樣品中的腫瘤壞死因子α(TNF-α)呈正相關。用酶標儀在450nm波長下測定吸光度(OD值),通過標準曲線計算樣品中羊腫瘤壞死因子α(TNF-α)濃度。