欧美……一区二区三区,欧美日韩亚洲另类视频,亚洲国产欧美日韩中字,日本一区二区三区dvd视频在线

產品推薦:氣相|液相|光譜|質譜|電化學|元素分析|水分測定儀|樣品前處理|試驗機|培養箱


化工儀器網>技術中心>操作使用>正文

歡迎聯系我

有什么可以幫您? 在線咨詢

綿羊γ氨基丁酸(GABA)酶聯免疫分析(ELISA)

來源:上??ㄅ锟萍加邢薰?nbsp;  2019年04月17日 09:49  

綿羊γ氨基丁酸GABA酶聯免疫分析(ELISA)

試劑盒使用說明書

本試劑僅供研究使用       目的:本試劑盒用于測定綿羊血清、血漿、組織勻漿及相關液體樣本中γ氨基丁酸(GABA)的含量。

 

實驗原理

本試劑盒應用雙抗體夾心法測定標本綿羊γ氨基丁酸(GABA)水平。用純化的綿羊γ氨基丁酸(GABA)捕獲抗體包被微孔板,制成固相體,往包被的微孔中依次加入綿羊γ氨基丁酸(GABA),再與HRP標記的檢測抗體結合,形成抗體-抗原-酶標抗體復合物,經過*洗滌后底物TMB顯色。TMB在HRP酶的催化下轉化成藍色,并在酸的作用下轉化成終的黃色。顏色的深淺和樣品中的綿羊γ氨基丁酸(GABA)呈正相關。用酶標儀在450nm波長下測定吸光度(OD值),通過標準曲線計算樣品綿羊γ氨基丁酸(GABA)含量。

 

試劑盒組成

試劑盒組成

48孔配置

96孔配置

保存

說明書

1份

1份

 

封板膜

2片

2片

 

密封袋

1個

1個

 

酶標包被板

1×48

1×96

2-8℃保存

標準品

0.3ml×6管

0.3ml×6管

2-8℃保存

酶標試劑

5 ml×1瓶

10 ml×1瓶

2-8℃保存

樣品稀釋液

3 ml×1瓶

6 ml×1瓶

2-8℃保存

顯色劑A液

3 ml×1瓶

6 ml×1瓶

2-8℃保存

顯色劑B液

3 ml×1瓶

6 ml×1瓶

2-8℃保存

終止液

3 ml×1瓶

6 ml×1瓶

2-8℃保存

20×濃縮洗滌液

15ml×1瓶

25ml×1瓶

2-8℃保存

注:標準品濃度依次為:8、4、2、1、0.5、0 μmol/L.

 

樣本處理及要求

1. 血清:室溫血液自然凝固10-20分鐘,離心20分鐘左右(2000-3000轉/分)。仔細收集上清,保存過程中如出現沉淀,應再次離心。

2. 血漿:應根據標本的要求選擇EDTA或檸檬酸鈉作為抗凝劑,混合10-20分鐘后,離心20分鐘左右(2000-3000轉/分)。仔細收集上清,保存過程中如有沉淀形成,應該再次離心。

3. 尿液:用無菌管收集,離心20分鐘左右(2000-3000轉/分)。仔細收集上清,保存過程中如有沉淀形成,應再次離心。胸腹水、腦脊液參照實行。

4. 細胞培養上清:檢測分泌性的成份時,用無菌管收集。離心20分鐘左右(2000-3000轉/分)。仔細收集上清。檢測細胞內的成份時,用PBS(PH7.2-7.4)稀釋細胞懸液,細胞濃度達到100萬/ml左右。通過反復凍融,以使細胞破壞并放出細胞內成份。離心20分鐘左右(2000-3000轉/分)。仔細收集上清。保存過程中如有沉淀形成,應再次離心。

5. 組織標本:切割標本后,稱取重量。加入一定量的PBS,PH7.4。用液氮迅速冷凍保存?zhèn)溆?。?biāo)本融化后仍然保持2-8℃的溫度。加入一定量的PBS(PH7.4),用手工或勻漿器將標本勻漿充分。離心20分鐘左右(2000-3000轉/分)。仔細收集上清。分裝后一份待檢測,其余冷凍備用。

6. 標本采集后盡早進行提取,提取按相關文獻進行,提取后應盡快進行實驗。若不能馬上進行試驗,可將標本放于-20℃保存,但應避免反復凍融.

7. 不能檢測含NaN3的樣品,因NaN3抑制辣根過氧化物酶的(HRP)活性。

 

操作步驟

  1. 標準品的加樣:設置標準品孔和樣本孔,標準品孔各加不同濃度的標準品50μL;。
  2. 加樣:分別設空白孔(空白對照孔不加樣品及酶標試劑,其余各步操作相同)、待測樣品孔。在酶標包被板上待測樣品孔中先加樣品稀釋液40μl,然后再加待測樣品10μl(樣品終稀釋度為5倍)。加樣將樣品加于酶標板孔底部,盡量不觸及孔壁,輕輕晃動混勻。
  3. 加酶:每孔加入酶標試劑100μl,空白孔除外。
  4. 溫育:用封板膜封板后置37℃溫育60分鐘
  5. 配液:將20倍濃縮洗滌液用蒸餾水20倍稀釋后備用。
  6. 洗滌:小心揭掉封板膜,棄去液體,甩干,每孔加滿洗滌液,靜置30秒后棄去,如此重復5次,拍干。
  7. 顯色:每孔先加入顯色劑A50μl,再加入顯色劑B50μl,輕輕震蕩混勻,37℃避光顯色15分鐘.
  8. 終止:每孔加終止液50μl,終止反應(此時藍色立轉黃色)
  9. 測定:以空白孔調零,450nm波長依序測量各孔的吸光度(OD值)。 測定應在加終止液后15分鐘以內進行。

 

注意事項:

  1. 試劑盒從冷藏環境中取出應在室溫平衡15-30分鐘后方可使用,酶標包被板開封后如未用完,板條應裝入密封袋中保存。
  2. 濃洗滌液可能會有結晶析出,稀釋時可在水浴中加溫助溶,洗滌時不影響結果。
  3. 各步加樣均應使用加樣器,并經常校對其準確性,以避免試驗誤差。一次加樣時間控制在5分鐘內,如標本數量多,推薦使用排槍加樣。
  4. 請每次測定的同時做標準曲線,做復孔。如標本中待測物質含量過高(樣本OD值大于標準品孔孔的OD值),請先用樣品稀釋液稀釋一定倍數(n倍)后再測定,計算時請后乘以總稀釋倍數(×n×5)。
  5. 封板膜只限一次性使用,以避免交叉污染。
  6. 底物請避光保存。
  7. 嚴格按照說明書的操作進行,試驗結果判定必須以酶標儀讀數為準.
  8. 所有樣品,洗滌液和各種廢棄物都應按傳染物處理。
  9. 本試劑不同批號組分不得混用。

10. 如與英文說明書有異,以英文說明書為準。

 

 

 

計算

以標準物的濃度為橫坐標,OD值為縱坐標,   

在坐標紙上繪出標準曲線,根據樣品的OD     

值由標準曲線查出相應的濃度;再乘以稀釋      

倍數;或用標準物的濃度與OD值計算出標     

準曲線的直線回歸方程式,將樣品的OD值     

代入方程式,計算出樣品濃度,再乘以稀釋      

倍數,即為樣品的實際濃度。                 

 

                                             

 

(此圖僅供參考)

 

 

 

試劑盒性能:

1.樣品線性回歸與預期濃度相關系數R值為0.95以上。

2.批內變異系數與批間變異系數應分別小于10%和15% 。

 

檢測范圍:                                              

0.25 μmol/L - 8 μmol/L

 

靈敏度:                                              

低檢測濃度小于0.1 μmol/L

 

保存條件及有效期:

1.試劑盒保存: 2-8。

2.有效期: 6個月


Sheep Gamma-aminobutyric acid

FOR RESEARCH USE ONLY

 

Drug Names

Generic NameSheep Gamma-aminobutyric acid (GABA) ELISA Kit.

Purpose

This kit allows for the determination of GABA concentrations in Sheep serum, plasma, tissue homogenates and other biological fluids.

Principle of the assay

The kit assay Sheep GABA level in the sample, use Purified Sheep GABA antibody to coat microtiter plate wells, make solid-phase antibody, then add GABA to the wells, Combined antibody which With HRP labeled, become antibody-antigen-enzyme-antibody complex, after washing Completely, Add TMB substrate solution,TMB substrate becomes blue color At HRP enzyme-catalyzed, reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm. The concentration of GABA in the samples is then determined by comparing the O.D. of the samples to the standard curve.


Materials provided with the kit

Materials provided with the kit

48determinations

96 determinations

Storage

User manual

1

1

 

Closure plate membrane

2

2

 

Sealed bags

1

1

 

Microelisa stripplate

1

1

2-8℃

Standard

0.3ml×6 bottle

0.3ml×6 bottle

2-8℃

HRP-Conjugate reagent

5ml×1 bottle

10ml×1 bottle

2-8℃

Sample diluent

3ml×1 bottle

6ml×1 bottle

2-8℃

Chromogen Solution A

3ml×1 bottle

6ml×1 bottle

2-8℃

Chromogen Solution B

3ml×1 bottle

6ml×1 bottle

2-8℃

Stop Solution

3ml×1 bottle

6ml×1 bottle

2-8℃

20×Wash solution

15ml×1 bottle

25ml×1 bottle

2-8℃

Note: Standard concentration was followed by:

8、4、2、1、0.5、0 μmol/L.

Specimen requirements

  1. serum- coagulation at room temperature 10-20 mins,centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant, If precipitation appeared, Centrifugal again.
  2. plasma-use suited EDTA or citrate plasma as an anticoagulant,mix 10-20 mins ,centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant, If precipitation appeared, Centrifugal again.
  3. Urine-collect sue a sterile container, centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant, If precipitation appeared, Centrifugal again. The Operation of Hydrothorax and cerebrospinal fluid Reference to it.
  4. cell culture supernatant-detect secretory components, collect sue a sterile container, centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant,detect the composition of cells, Dilut cell suspension with PBS(PH7.2-7.4), Cell concentration reached 1 million / ml, repeated freeze-thaw cycles, damage cells and release of intracellular components, centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant, If precipitation appeared, Centrifugal again.
  5. Tissue samples- After cutting samples, check the weight,add PBS(PH7.2-7.4), Rapidly frozen with liquid nitrogen, maintain samples at 2-8 after melting,add PBSPH7.4, Homogenized by hand or Grinders, centrifugation 20-min at the speed of 2000-3000 r.p.m. remove supernatant.
  6. extract as soon as possible after Specimen collection,and according to the relevant literature, and should be experiment as soon as possible after the extraction. If it cant, specimen can be kept in -20  to preserve, Avoid repeated freeze-thaw cycles.
  7. Can’t detect the sample which contain NaN3, because NaN3 inhibits HRP active.

Assay procedure

1. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.

2.add sampleSet blank wells separately (blank comparison wells don’t add sample and HRP-Conjugate reagent, other each step operation is same). testing sample well. add Sample dilution 40μl to testing sample well, then add testing sample 10μl (sample final dilution is 5-fold), add sample to wells , don’t touch the well wall as far as possible, and Gently mix.

3.add enzymeAdd HRP-Conjugate reagent 100μl to each well, except  blank well.

4.Incubate: After closing plate with Closure plate membrane ,incubate for 60 min at 37.

5.Configurate liquid: 20-fold wash solution diluted 20-fold with distilled water and reserve.

6.washingUncover Closure plate membrane, discard Liquid, dry by swing, add washing buffer to every well, still for 30s then drain, repeat 5 times, dry by pat.

7.color:Add Chromogen Solution A 50ul and Chromogen Solution B to each well, evade the light preservation for 15 min at 37

8.Stop the reaction:Add Stop Solution 50μl to each well, Stop the reaction(the blue color change to yellow color).

9.assay:take blank well as zero , Read absorbance at 450nm after Adding Stop Solution and within 15min.


Important notes

  1. The kit takes out from the refrigeration environment should be balanced 15-30 minutes in the room temperature, ELISA plates coated if has not use up after opened, the plate should be stored in Sealed bag.
  2. washing buffer will Crystallization separation, it can be heated the water helps dissolve when dilute . Washing does not affect the result.
  3. add Sample with sampler Each step, And proofread its accuracy frequently, avoids the experimental error. add sample within 5 mins, if the number of sample is much , recommend to use Volley .
  4. if the testing material content is excessively higher (The sample OD is bigger than the first standard well ),please dilute Sample (n-fold), Please diluente and multiplied by the dilution factor.(×n×5).
  5. Closure plate membrane only limits the disposable use, to avoid cross-contamination.
  6. The substrate evade the light preservation.
  7. Please according to use instruction strictly, The test result determination must take the microtiter plate reader as a standard.
  8. All samples, washing buffer and each kind of reject should according to infective material process.
  9. Do not mix reagents with those from other lots.


Calculate

 

 

 

 

 

 

 

 

 

Assay range

0.25 μmol/L - 8 μmol/L

 

Sensitivity

The minimum detectable dose is typically less than 0.1 μmol/L

 

Storage and validity

1.Storage:  2-8.

2.validity: six months.

相關產品

免責聲明

  • 凡本網注明“來源:化工儀器網”的所有作品,均為浙江興旺寶明通網絡有限公司-化工儀器網合法擁有版權或有權使用的作品,未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的,應在授權范圍內使用,并注明“來源:化工儀器網”。違反上述聲明者,本網將追究其相關法律責任。
  • 本網轉載并注明自其他來源(非化工儀器網)的作品,目的在于傳遞更多信息,并不代表本網贊同其觀點和對其真實性負責,不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時,必須保留本網注明的作品第一來源,并自負版權等法律責任。
  • 如涉及作品內容、版權等問題,請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系,否則視為放棄相關權利。
企業未開通此功能
詳詢客服 : 0571-87858618
欧美激情一区二区三区啪啪| 丰满成熟少妇被猛烈进入| 国产三级av高清一区二区| 丰满熟妇久久久人妻av| 91精品国模一区二区三区| 丰满的熟妇露脸大屁股| 国产成人久久精品二三区| 日本女优中文字幕人妻| 精品日韩人妻一区二区三区| 亚洲香艳网久久五月婷婷| 欧美一二三区综合在线| 日韩一级欧美一级黄片| 极品少妇高潮久久添久久| 亚洲精品日韩国产欧洲精品| 男生看的污网站推荐免费| 精品少妇人妻av一区| 又粗又黄又爽的国产视频| 日韩av在线永久免费| 猛烈进入请清纯露脸少妇| 久久亚洲精品一二三区| 丰满少妇啪中文字幕一区| 亚洲国产成人久久精品蜜臀| 亚洲欧美在线激情视频| 欧美国产日韩一区二区在线观看| 成人精品18一区二区| 久久久av一区二区三| 国产精品成人免费av| 精品国产成人国产在线视| 亚洲av久久中文字幕| 少妇十八毛片毛片毛片| 日韩激情视频在线播放| 色哟哟精品中文字幕乱码| 国产成人精品自在线拍| 国产中文av网在线播放| 亚洲黄色手机在线播放| 久久99亚洲国产精品| 91一区二区三精品人妻| 亚洲淑女少妇一区二区三区| 亚洲熟女精品区一区二三| 日韩国产主播av在线| 亚洲欧美日韩av在线|